AUTOSAR Classic Ethernet Services

This function is to be used by integrators to inform the DoIP implementation about the status of the activation line of a DoIP interface with given InterfaceId.

Call with argument NonTlsAllowed==TRUE to allow unsecured DoIP connection establishments. If called with NonTlsAllowed==FALSE, DoIP will close the unsecured connection with NRC 0x07 and require the tester to use TLS.

Returns the version information of this module.

Requests cancellation of an ongoing transmission of a PDU in a lower layer communication module.

Requests transmission of a PDU.

This service initializes all global variables of the DoIP module. After return of this service the Do IP module is operational.

This function gets called by the SoAd if an IP address assignment related to a socket connection changes (i.e. new address assigned or assigned address becomes invalid).

Schedules the Diagnostic over IP module. (Entry point for scheduling)

Indication of a received PDU from a lower layer communication interface module.

The lower layer communication interface module confirms the transmission of a PDU, or the failure to transmit a PDU.

This function is called to provide the received data of an I-PDU segment (N-PDU) to the upper layer. Each call to this function provides the next part of the I-PDU data. The size of the remaining buffer is written to the position indicated by bufferSizePtr.

This function is called to acquire the transmit data of an I-PDU segment (N-PDU). Each call to this function provides the next part of the I-PDU data unless retry->TpDataState is TP_ DATARETRY. In this case the function restarts to copy the data beginning at the offset from the current position indicated by retry->TxTpDataCnt. The size of the remaining data is written to the position indicated by availableDataPtr.

Called after an I-PDU has been received via the TP API, the result indicates whether the transmission was successful or not.

This function is called at the start of receiving an N-SDU. The N-SDU might be fragmented into multiple N-PDUs (FF with one or more following CFs) or might consist of a single N-PDU (SF). The service shall provide the currently available maximum buffer size when invoked with TpSdu Length equal to 0.

This function is called after the I-PDU has been transmitted on its network, the result indicates whether the transmission was successful or not.

Notification about a SoAd socket connection state change, e.g. socket connection gets online

Requests cancellation of an ongoing reception of a PDU in a lower layer transport protocol module. The call of this API to cancel an ongoing reception will close the used TCP connection.

Requests cancellation of an ongoing transmission of a PDU in a lower layer communication module. The call of this API to cancel an ongoing transmission will close the used TCP connection.

Requests transmission of a PDU.

This function is used to notify the DoIP module to start vehicle announcement for DoIP interfaces with given InterfaceId. This function is just a trigger to start the DoIPInitialVehicle AnnouncementTime timeout.

Callback function to get the OEM specific Further Action Byte for the DoIP vehicle identification response/vehicle announcement.

Function is used in the case that DoIPVinGIDMaster is set to false and DoIPGetGidCallback is configured to get on a vehicle identification the GID. If the return value is not E_OK the DoIP shall use the default GID.

Callback function to check if the PowerMode of the DoIP entity is ready or not.

Callback function to get the confirmation for the Routing Activation.

Callback function to get the confirmation for the Routing Activation.

Function is used in the case that DoIPVinGIDMaster is set to true and a container DoIPTrigger GidSyncCallback is configured to trigger the synchronization process of the GroupIdentifier.

Variation Name = {ecuc(DoIP/DoIPConfigSet/DoIPInterface/DoIPRoutingActivation.SHORT-NAME)}

Variation Name = {ecuc(DoIP/DoIPConfigSet/DoIPRoutingActivation.SHORT-NAME)}

Variation Name = {ecuc(DoIP/DoIPConfigSet/DoIPRoutingActivation.SHORT-NAME)}

Variation Name = {ecuc(DoIP/DoIPConfigSet/DoIPRoutingActivation.SHORT-NAME)}

Configuration data structure of the DoIP module

Used to get the OEM specific Further Action Byte for the DoIP vehicle identification response/ vehicle announcement. Variation –

Used for handling of the PowerMode in DoIP entity status requests Variation –

Activat es egress time stamping on a dedicated message object. Some HW does store once the egress time stamp marker and some HW needs it always before transmission. There will be no "disable" functionality, due to the fact, that the message type is always "time st amped" by network design.

Obtains the state of the indexed controller Tags: atp.Status=obsolete

Obtains the communication state of the indexed controller Tags: atp.Status=draft

Reads a list with drop counter values of the corresponding controller. The meaning of these values is described at Eth_ Counter Type.

Returns a time value out of the HW registers according to the capability of the HW. Is the HW resolution is lower than the Eth_ Time Stamp Type resolution resp. range, than an the remainin g bits will be filled with 0. Important Note: Eth_ Get Current Time may be called within an exclusive area.

Reads back the egress time stamp on a dedicated message object. It must be called within the Tx Confirmation() function.

Reads back the ingress time stamp on a dedicated message object. It must be called within the Rx Indication() function.

Obtains the physical source address used by the indexed controller

Returns the following list according to IETF RFC281 9, where the maximal possible value shall denote an invalid value, e.g. if this counter is not available: 1. ether Stats Drop Events 2. ether Stats Octets 3. ether Stats Pkts 4. ether Stats Broadcast Pkts 5. ether Stats Multicast Pkts 6. ether Stats Crc Al ign Errors 7. ether Stats Undersize Pkts 8. ether Stats Oversize Pkts 9. ether Stats Fragments 10. ether Stats Jabbers 11. ether Stats Collisions 12. ether Stats Pkts64Octets 13. ether Stats Pkts65to127Octets 14. ether Stats Pkts128to255Octets 15. ether St ats Pkts256to511Octets 16. ether Stats Pkts512to1023Octets 17. ether

Returns the list of Transmission Error Counters out of IETF RFC1213 and RFC1643 defined with Eth_ Tx Error Counter Values Type, where the maximal possible value shall denote an invalid value, e.g. this counter is not available.

Returns the list of Transmission Statistics out of IETF RFC1213 defined with Eth_ Tx Stats Type, where the maximal possible value shall denote an invalid value, e.g. this counter is not available.

Returns the version information of this module

Initializes the Ethernet Driver

The function checks for controller errors and lost frames. Used for polling state changes. Calls Eth If_ Ctrl Mode Indication when the controller mode changed.

Provides access to a transmit buffer of the FIFO related to the specified priority

Reads a transceiver register

Receive a frame from the related fifo.

Enables / disables the indexed controller Tags: atp.Status=obsolete

Enables / Disables Rx/ Tx communication of the indexed controller Tags: atp.Status=draft

Sets the physical source address used by the indexed controller

Triggers transmission of a previously filled transmit buffer

Triggers frame transmission confirmation

Update the physica l source address to/ from the indexed controller filter. If the Ethernet Controller is not capable to do the filtering, the software has to do this.

Configures a transceiver register or triggers a function offered by the receiver

Ethernet buffer identifier type.

Implementation specific structure of the post build configuration

Type Eth_CounterType.

This type defines the Ethernet data type used for data transmission. Its definition depends on the used CPU.

The Enumeration Type Eth_ Filter Action Type describes the action to be taklen for the MAC address given in *Phys Addr Ptr.

This type defines the Ethernet frame type used in the Ethernet frame header

This type is used to read out addresses from the address resolution logic (A RL) table of the switch. typedef struct { uint8 Mac Addr[6U]; uint16 Vlan Id; uint32 Switch Port; } Eth_ Mac Vlan Type; In case of Macaddr contains a Multicast Address Mac Vlan Type.Switch Port shall be handled as Bitmask, each bit represents a Switch Port , Bit 0 represents Eth Swicht Port Idx = 0 , Bit 1 represents Eth Swicht Port Idx = 1 and so on. In case of Macaddr contains not a Multicast Address Mac Vlan Type.Switch Port shall be handled as a value representing the Eth Switch Port Idx.

This is an generic type and used in the layers of the Ethernet communication stack (e.g. EthIf, Eth, EthSwt, EthTrcv) to enable and disable, resp ectively, the Ethernet communcation channel and set the corresponding hardware (e.g. Ethernet controller, Ethernet Switch port, Ethernet transceiver) to an lowpower sleep and power on mode, respectively. Tags: atp.Status=obsolete

This is an generic type and used in the layers of the Ethernet commun ication stack (e.g. Eth If, Eth, Eth Swt, Eth Trcv) to enable and disable, respectively, the Ethernet communcation channel and set the corresponding hardware (e.g. Ethernet controller, Ethernet Switch port, Ethernet transceiver) to an lowpower sleep and po wer on mode, respectively. The type also support to transfer a wake - up request from the services layer (Com M) to the communication drivers (Eth Trcv). This could be used e.g. for Ethernet hardware that has the capability to wake - up and sleep on data line (see OA TC10) Tags: atp.Status=draft

Variables of this type are used to express frequency ratios.

Type Eth_RxStatsType.

Used as out parameter in Eth_ Receive() indicates whether a frame has been received and if so, whether more frames are available or frames go t lost.

Status supervision used for Development Error Detection. The state shall be available for debugging.

Variables of this type are used to express time differences.

Depending on the HW, quality information regarding the evaluated time stamp might be supported. If not supported, the value shall be always Valid. For Uncertain and Invalid values, the upper layer shall discard the time stamp.

Variables of this type are used for expressing time stamps including relative time and absolute calendar time. The absolute time starts at 1970 - - 01. 0 to 281474976710655s == 3257812230d [0x FFFF FFFF FFFF] 0 to 999999999ns [0x3B9A C9FF] invalid value in nanoseconds: [0x3B9A CA00] to [0x3FFF FFFF] Bit 30 and 31 reserved, default: 0

Type Eth_TxErrorCounterValuesType.

Statistic counter for diag nostics.

This API request the affected Ethernet hardware to c heck for a signaled wake - up. The used Ethernet hardware could be an Ethernet switch or Ethernet transceiver (PHY). This is used e.g. for Ethernet hardware which is compliant to the specification of Open Alliance TC10. This API is called by the integration code. The function could be called in context of the interrupt or on task level.

Clear the stored signal quality of the link of the given Et hernet switch port

Clear the stored signal quality of the link of the given Ethernet transceiver

Called asynchronously when mode has been read out. Triggered by previous Eth_ Set Controller Mode call. Can directly be called within the trigger functions.

Delete the stored port mirror configuration of the given Mirrored Switch Idx. If no port mirror configuration was found for the given Mirrored Switch Idx, the return value shall be E_ OK.

Activates egress time stamping on a dedicated message object. Some HW does store once the egress time stamp marker and some HW needs it always before transmission. There will be no "disable" functionality, due to the fact, that the message type is always " time stamped" by network design.

Allows to read and reset detailed measurement data for diagnostic purposes. Get all Measurement Idx's at once is not supported. ETHIF_ MEAS_ ALL shall only be used to reset all Measurement Idx's at once. A NULL_ PTR shall be provided for Measurement Data Ptr in this case.

Obtains the address resolution ta ble of a switch and copies the list into a user provided buffer. The function will copy all or number Of

Read out values related to the receive direction of the transceiver for a received packet. For example, this could be RSSI or Channel belonging to one single packet.

Read out values related to the transmit direction of the transceiver for a transmitted packet. For example, this could be transaction ID belonging to one single packet.

Retrieves the cable diagnostics result of a given transceiver.

Read values related to the receive direction of the transceiver. For example, this could be a Channel Busy Ratio (CBR) or the average Channel Idle Time (CIT).

Obtains the state of the ind exed controller

Returns the number and index of all active Ethernet controllers.

Returns a time value out of the HW registers according to the capability of the HW. Is the HW resolution is lower than the Eth_ Time Stamp Type resolution resp. range, the remaining bits will be filled with 0. Important Note: Eth If_ Get Curren t Time may be called within an exclusive area.

Reads back the egress time stamp on a dedicated message object. It must be called within the Tx Confirmation() function.

Reads back the ingress time stamp on a dedicated message object. It must be called within the Rx Indication() function.

Obtains the PHY identifier of the Ethernet Interface according to IEEE 802.3 - chapter 22.2.4.3.1 PHY Identifer.

Obtains the physical source address used by the indexed controller

Tags: atp.Status=draft

Retrieves the cable diagnostics result of the indexed Ethernet switch port respectively the referenced Ethernet Transceiver Driver.

Obtains the port over which this MAC - address can be reached

Obtain the current status of the port mirroring for the indexed Ethernet switch port

Request the Mgmt Object of the (in this context) unique Data Ptr.

Obtain the Organizationally Unique Identifier that is given by the IEEE of the indexed Ethernet switch. This function shall provide the OUI of Ethernet switch. The OUI has a size of 24 bit. If a ethernet switch can provide the OUI the 8 most significant bits of the OUI shall be set to 0x00xxxxxx. If a Ethernet switch can not provide the OUI the 8 most significant bits of the OUI shall be set to 0x FFxxxxxx. Availa ble via Eth If.h

This function retrieves the OUI (24 bit) of the indexed Ethernet switch port.

Obtains the mode of the indexed switch port

Retrieves the signal quality of the link of the given Ethernet switch port

This function obtains the wake up reasons of the indexed Ethernet switch port by

Obtains the state of the indexed transceiver

Returns the wake up mode of the indexed tran sceiver Tags: atp.Status=obsolete

Retrieves the signal quality of the link of the given Ethernet transceiver

Request the Mgmt Object of the (in this context) unique Buf Idx.

Returns the version information of this module

Returns the VLAN identifier of the requested Ethernet controller.

Initializes the Ethernet Interface

The function checks for new received frames and issues reception indications in polling mode.

The function is polling different communication hardware (Ethernet transceiver, Ethernet switch ports) related information, e.g. link state, signal quality.

The function issues transmission confirmations in polling mode. It checks also for transceiver state changes.

Provides access to a transmit buffer of the specified Ethernet controller.

Obtain the port mirror configuration of the given Ethernet switch.

The function shall request to reset the configuration of the learned MAC/ Port tables of a Eth ernet switch in a persistent manner. This could be used by e.g. a CDD. The statically configured entries shall still remain.

Trigger the cable diagnostics for the given Ethernet transceiver.

Trigger the cable diagnostics of the given Ethernet Switch port (Port Idx) by calling Eth Trcv_ Run Cable Diagnostic of the referenced Ethernet transceiver.

Handles a received frame received by the indexed controller

Set values related to the transmit direction of the transceiver for a specific buffer (packet to be sent). For example, this can be the desired transmit power or the channel belonging to one single packet.

Set values related to the receive direction of a transceiver's wireless channel. For example, this could be a channel parameter like the frequency.

Set values related to the transmit direction of a transceiver's wireless channel. For example, this could be the bitrate of a channel.

Enables / disables the indexed controller thernet Interface AUTOSAR CP R20 - of Document ID : AUTOSAR_SWS_EthernetInterface

Verifies the Switch Configuration. If Configuration is not valid, Switch is reconfigured.

Activates a given loopback mode.

Sets the physical source address used by the indexed controller.

Activates a given test mode.

Activates a given transmission mode. Tags: atp.Status=draft

Activates a given test loop - back mode of the indexed Ethernet switch port.

Request to set the given port mirroring state of the port mirror configuration for the given Ethernet switch.

Activates a given test mode of the indexed Ethernet switch port.

Activates a given transmission mode of the indexed Ethernet switch port.

Set values related to a transceiver's wireless radio. For example, this could be the selection of the radio settings (channel, ...).

Provides additional management information along to an Ethernet frame that requires special treatment within the Switch. It has to be called between Eth If_ Provide Tx Buffer() and Eth If_ Transmit() of the related frame.

Enables / disables the wake up mode or clear the wake - up reason of the indexed transceiver Tags: atp.Status=obsolete

This API is called by the corresponding Eth Trcv, if a sleep indication was detected on the network. This could be used e.g. for Ethernet hardware which is compliant to the OA TC10. In this ca se the Ethernet hardware (PHY) detect an Sleep.Indication which was triggered by a Sleep.Request of the connected link partner. Tags: atp.Status=draft

Request to set all configured and affected Eth Swt Ports to ETH_ MODE_ ACTIVE

The function shall request to store the configuration of the learned MAC/ Port tables of a Ethernet switch in a persistent manner. This could be used by e.g. a CDD.

Activates egress time stamping on a dedicated message object, addressed by Ctrl Idx and Buf Idx.

Retrieves the total size of data and the memory start address of the indexed Ethernet Switch.

Retrieves the data in memory of the indexed Ethernet switch in variable length

Obtains the baud rate of the indexed switch port

Reads a list with drop counter values of the corresponding port of the switch. The meaning of these values is described at Eth_ Counter Type.

Obtains the duplex mode of the indexed switch port

Obtains the link state of the indexed switch port

Returns the MAC learning mode, i.e. 1.) HW learning enabled, 2.) Hardware l earning disabled, 3.) Software learning enabled. Note: This feature is hardware dependent, i.e. the switch hardware needs to support the different learning modes

Service EthIf_SwitchPortGetMaxFIFOBufferFillLevel.

Returns a list of statistic counters defined with E th_ Rx Tats Type. The majority of these Counters are derived from the IETF RFC2819.

Returns the list of Transmission Error Counters out of IETF RFC1213 and RFC16 defined with Eth_ Tx Error Counter Values Type, where the maximal possible value shall denote an invalid value, e.g. this counter is not available.

Returns the list of Transmission Statistics out of IETF RFC1213 defined with Eth_ Tx Stats Type, where the maximal possible value shall denote an invalid value, e.g. this counter is not available.

Request a mode for the Eth If Swt Port Group. The call shall be forwarded to Eth Swt by calling Eth Swt_ Set Switch P ort Mode for all Eth Swt Ports referenced by the port group.

The Eth If shall determine the expected notifications based on the Eth Swt Port configuration. In case the Eth Swt Port references an Eth Trcv the Eth If expects a notification from the Eth Trcv via API Eth If_ Trcv Mode Indication(). Otherwise the Eth If expects a notification from the Eth Swt via API Eth If_ Switch Port Mode Indication()

Obtains the baud rate of the indexed transceiver

Obtains the duplex mode of the indexed tra nsceiver

Obta ins the link state of the indexed transceiver

Obtains the media access mode of the transceiver. Tags: atp.Status=draft thernet Interface AUTOSAR CP R20 - of Document ID : AUTOSAR_SWS_EthernetInterface

Triggers transmission of a previously filled transmit buffer

Called asynchronously when a mode change has been read out. If the function is triggered by previous call of Eth Trcv_ Set Transceiver Mode it can directly be called within the trigger function. Ava ilable via Eth If.h

Confirms frame transmission by the indexed controller

Update the physical source address to/ from the indexed controller filter. If the Ethernet Controller is not capable to do the filtering, the software has to do this.

Forwarded t o Eth Swt_ Verify Config. Eth Swt_ Verify Config verifies the Switch thernet Interface AUTOSAR CP R20 - of Document ID : AUTOSAR_SWS_EthernetInterface Configuration depending on the HW - Architecture, HW - capability and the intended accuracy of this verification.

Service EthIf_WritePortMirrorConfiguration.

Implementation specific structure of the post build configuration

Index to select specific measurement data

-

Data Type that represents the Ethernet interface switch port group index. The index is zero based and unique for every configured switch port group.

Called when mode has been read out. Either triggered by previous Eth If_ Get Controller Mode or by Eth If_ Set Controller Mode call. Can directly be called within the trigger functions.

This service shall put out the current communication mode of a Ethernet network.

This service puts out the version information of this module.

This function initialize the Eth SM.

Cyclic Main Function which is called from the Scheduler.

Handles the communication mode and sets the Ethernet network active or passive.

This API is called by the Eth If and indicate that a sleep indication was detected on the network. This API is only called if the ECU is acting as a passive communication slave on the corresponding communication channel (the referenced Eth Trcv of the affe cted Eth If Transceiver has set Eth Trcv Act As Slave Passive Enabled to TRUE). This could be used e.g. for Ethernet hardware which is compliant to the OA TC10. In this case the Ethernet hardware detect an Sleep.Indication which was triggered by a Sleep.Re quest of the connected link partner. Tags: atp.Status=draft

This service is called by the Tcp Ip to report the actual Tcp Ip state (e.g. online, offline). Available vi a Eth SM_ Tcp Ip.h

This service is called by the Ethernet Interface to report a transceiver link state change.

This type shall define the states of the network mode state machine.

Is called, if a link which is configured goes down.

Is called, if a link which is configured goes up

Job end notification of EthSwt_StoreConfiguration or EthSwt_ResetConfiguration

The call of the function EthSwt_GetCfgDataRaw() triggers a asynchrony read of a certain memory section of the Ethernet switch driver. If the read is done, the configured callout function <GetCfgDataRawDone> shall be called]

The background task should be scheduled as often as possible when no other task runs. It may be used for switch and port initialization in case the EthSwt_Init function needs too much time.

API is called by EthIf. The Ethernet switch driver request to check for a wake-up at all Ethernet switch ports which reference an EthTrcv. For those Ethernet switch ports the call is forwarded to the referenced EthTrcv. The function could be called in context of an interrupt service routine or on task level Note: Interrupt service routine consuming time has to be considered, since all EthSwtPorts of the maintained Ethernet switches has to be checked. Therefore the call is forwarded to the referred EthTrcv where the request to check for wake-up is stored. The check of the Ethernet hardware is done asynchronously in the context of the EthTrcv_MainFunction.

Delete the stored port mirror configuration of the given MirroredSwitchIdx. If no port mirror configuration was found for the given MirroredSwitchIdx, the return value shall be E_OK.

Enables or disables a pre-configured VLAN at a certain port of a switch.

Indication for a finished receive process for a specific Ethernet frame, which results in providing the management information retrieved during EthSwt_EthRxProcessFrame().

Function inspects the Ethernet frame passed by the data pointer for management information and stores it for later use in EthSwt_EthRxFinishedIndication().

Modifies the buffer length to be able to insert management information.

Indication for a finished transmit process for a specific Ethernet frame.

Prepares the Ethernet frame for common Ethernet communication (frame shall be handled by switch according to the common address resolution behavior) and stores the information for processing of EthSwt_EthTxFinishedIndication().

Function inserts management information into the Ethernet frame.

Extracts the StreamHandleIdx from the switch vendor specific part of the network packet header Tags: atp.Status=draft

Obtains the address resolution table of a switch and copies the list into a user provided buffer. The function will copy all or numberOfElements into the output list. If input value of numberOf Elements is 0 the function will not copy any data but only return the number of valid entries in the cache. arlTableListPointer may be NULL_PTR in this case.

Obtains the baud rate of the indexed switch port

Retrieves the total size of data and the memory start address of the indexed Ethernet Switch.

Retrieves the data in memory of the indexed Ethernet switch in variable length

Reads a list with drop counter values of the corresponding port of the switch. The meaning of these values is described at Eth_CounterType.

Obtains the duplex mode of the indexed switch port

Obtains the link state of the indexed switch port

Returns the MAC learning mode, i.e. 1.) HW learning enabled, 2.) Hardware learning disabled, 3.) Software learning enabled. Note: This feature is hardware dependent, i.e. the switch hardware needs to support the different learning modes

The function retrieves the maximum amount of allocated FIFO buffer of the indexed Ethernet switch egress port. If the Ethernet switch hardware does not support Ethernet switch port based maximal FIFO buffer level, the content of SwitchPortEgressFifoBufferLevelPtr shall be set to 0xFFFFFFFF. This API may be called by e.g. a CDD.

Retrieves the cable diagnostics result of the indexed Ethernet switch port respectively the referenced Ethernet Transceiver Driver.

This function retrieves the OUI (24 bit) of the indexed Ethernet switch port.

Obtains the port over which this MAC-address at the indexed switch can be reached. The result might be used for a DHCP-server which will need the port/MAC-resolution. If for the PortIdxPtr the maximal possible value (255) is returned the given MAC address cannot be reached via a port of this switch. If multiple ports were found the API returns E_NOT_OK.

Obtains an Ethernet switch port bit map, where the given MAC-address with respect to the given VLAN-ID is assigned to. The return argument PortBitMapPtr points to uint32 value which shall be handled as Ethernet switch port bit map. Each bit of the Ethernet switch port bit map represents an EthSwtPortIdx, where the least significant bit (bit 0) represents EthSwitchPortIdx 0 and most significant bit (bit 32) represents EthSwitchPortIdx 31 (e.g. 0x0001 == EthSwitch PortIdx 0 is set; 0x8005 == EthSwitchPortIdx 0, 2 and 31 are set).

Obtain the current status of the port mirroring for the indexed Ethernet switch port

The function retrieves the signal quality of the link of the indexed Ethernet switch port. If no transceiver is referenced the signal quality shall be set to 0xFFFFFFFF.

Obtains the MgmtObject of the (in this context) unique DataPtr.

Returns a list of statistic counters defined with Eth_RxTatsType. The majority of these Counters are derived from the IETF RFC2819.

Requests the bucket counter values from the switch Tags: atp.Status=draft

Obtain the Organizationally Unique Identifier that is given by the IEEE of the indexed Ethernet switch. This function shall provide the OUI of Ethernet switch. The OUI has a size of 24 bit. If a ethernet switch can provide the OUI the 8 most significant bits of the OUI shall be set to 0x00xxxxxx. If a Ethernet switch can not provide the OUI the 8 most significant bits of the OUI shall be set to 0xFFxxxxxx.

Obtains the mode of the indexed switch port

This function obtains the wake up reasons of the the indexed Ethernet switch port by calling Eth Trcv_GetBusWuReason(...) of the referenced EthTrcv

Generic API for reading the content of a switch register

Returns the list of Transmission Error Counters out of IETF RFC1213 and RFC1643 defined with Eth_TxErrorCounterValuesType, where the maximal possible value shall denote an invalid value, e.g. this counter is not available.

Obtains the MgmtObject of the (in this context) unique BufIdx.

Returns the list of Transmission Statistics out of IETF RFC1213 defined with Eth_TxStatsType, where the maximal possible value shall denote an invalid value, e.g. this counter is not available.

Returns the version information of this module.

Initializes the Ethernet Switch Driver

Request the Ethernet Switch Driver to create a Reception Secure Association in the Transceiver. The Short Secure Channel Identifier is included to support XPN configurations. Tags: atp.Status=DRAFT

Callback to notify that EthSwt_MacSecAddRxSa finished. Tags: atp.Status=DRAFT

Requests the Ethernet Switch Driver to create a Transmission Secure Association in the Transceiver. The Short Secure Channel Identifier is included to support XPN configurations. Tags: atp.Status=DRAFT

Callback to notify that EthSwt_MacSecAddTxSa finished. Tags: atp.Status=DRAFT

Request the Ethernet Switch Driver to remove the Reception Secure Association identified by the provided Association Number. Tags: atp.Status=DRAFT

Request the Ethernet Switch Driver to remove the Transmission Secure Association identified by the provided Association Number. Tags: atp.Status=DRAFT

Request the Ethernet Switch Driver to provide MACsec statistics. Tags: atp.Status=DRAFT

Callback to notify that EthSwt_MacSecGetMacSecStats finished and provide the requested statistics. Tags: atp.Status=DRAFT

Request the Ethernet Switch Driver to return the Packet Number that is used for the next packet in the given Transmission Secure Association. Tags: atp.Status=DRAFT

Requests the Ethernet Switch Driver to configure a Reception Secure Channel for the given Secure Channel Identifier. Tags: atp.Status=DRAFT

Requests the Ethernet Switch Driver to reset to default the MACsec values of the Reception Secure Channel for the given Secure Channel Identifier. Tags: atp.Status=DRAFT

Requests to set the Controlled Port enabled parameter of a PAE. Tags: atp.Status=DRAFT

Request the Ethernet Switch Driver to update the Reception Secure Association with the given Packet Number. The Active parameter is included to change the specified AN status. Tags: atp.Status=DRAFT

Requests the Ethernet Switch to update the SecY/PAC of the PHY with the provided parameters. A Transmission Secure Channel with the provided SCI shall be configured during the first call. A pointer to a MACsec Basic Parameters Configuration file shall be provided to create the Secure Channel. Tags: atp.Status=DRAFT

Callback to notify that EthSwt_MacSecUpdateSecY finished. Tags: atp.Status=DRAFT

Requests the Ethernet Switch Driver to update the Transmission Secure Association with the given Packet Number. The Active parameter is included to change the specified AN status. Tags: atp.Status=DRAFT

Service to support asynchronous behavior of API calls

Function will be called by the NVRAMManager after the switch configuration has been stored or resetted.

Activates egress time stamping on a dedicated message object on a dedicated port of a Switch if EthSwtPortTimeStampSupport is set to TRUE for this port. The selective activation of dedicated message objects for time stamping reduces the number of notification calls only to the required calls. Some HW does store once the egress time stamp marker and some HW needs it always before transmission. There will be no disabled functionality, due to the fact, that the message type is always "time stamped" by network design.

Request a link state by calling EthTrcv_TransceiverLinkStateRequest with the TrcvIdx of the Ethernet transceiver which is referenced by the Ethernet Switch port (PortIdx).

Reads a transceiver register using Clause 45 access if supported by hardware or implements a Clause 45 access using Clause 22 operations.

Obtain the port mirror configuration of the given Ethernet switch.

Generic API for reading the content of a transceiver register

The function shall request to reset and store the configuration of the learned MAC/Port tables of a Ethernet switch in a persistent manner. This could be used by e.g. a CDD.

Trigger the cable diagnostics of the given Ethernet Switch port (PortIdx) by calling EthTrcv_Run CableDiagnostic of the referenced Ethernet transceiver.

Configures switch to start or stop forwarding for all ports. This API call may be used during switch configuration verification.

Sets the MAC learning mode in one of the tree modes: 1.) HW learning enabled, 2.) Hardware learning disabled, 3.) Software learning enabled. Note: This feature is hardware dependent, i.e. the switch hardware needs to support the different learning modes.

Extends the Ethernet frame prepared previously by EthSwt_EthTxPrepareFrame() with the management information to achieve transmission only on specific ports.

Activates a given test loop-back mode of the indexed Ethernet switch port.

Request to set the given port mirroring state of the port mirror configuration for the given Ethernet switch.

Activates a given test mode of the indexed Ethernet switch port.

Activates a given transmission mode of the indexed Ethernet switch port.

This function is called by an upper layer application (e.g. diagnostic application) via the EthIf module to control the activity status of a configured stream (given with StreamHandleIdx) within an dedicated Ethernet switch (given with SwitchIdx). Tags: atp.Status=draft

Enables/disables the indexed switch port

Generic API for writing the content of a switch register

Starts the auto-negotiation of the indexed switch port

Trigger the storage/reset of the configuration of the learned MAC/Port tables of a switch in a persistent manner and will be used by e.g. CDD.

Verifies the Switch Configuration depending on the HW-Architecture, HW-capability and the intended accuracy of this verification.

Generic API for writing the content of a transceiver register

Store the given port mirror configuration in a shadow buffer in the Ethernet switch driver for the given MirroredSwitchIdx.

Generic API for writing the content of a transceiver register

Implementation specific structure of the post build configuration.

The interpretation of this value

Type for holding the management information received/transmitted on Switches (ports).

Provides information about all struct member elements. The ownership gives information whether EthSwt has finished its activities in providing all struct member elements.

Will be set from EthSwt and marks EthSwt_MgmtObject as valid or not. So the upper layer will be able to detect inconsistencies.

Holds information if upper layer or EthSwt is owner of mgmt_obj.

The EthSwt_PortMirrorCfgType specify the port mirror configuration which is set up per Ethernet switch. The configuration is written to the Ethernet switch driver by calling EthSwt_WritePortMirror Configuration. One port mirror configuration is maintained per Ethernet Switch.

Type to request or obtain the port mirroring state (enable/disable) for a particular port mirror configuration per Ethernet switch.

Status supervision used for Development Error Detection. The state shall be available for debugging.

Indicates an wake-up request for the specified Ethernet Transceiver. The given TrcvMode indicates if the request is based on a remote request from the network (ETH_MODE_ACTIVE) or if the request is based on active user request (ETH_MODE_ACTIVE_WITH_WAKEUP_ REQUEST). The callback function Ccan be used to trigger integrator code that initiates a remote wake-up .(e.g. trigger a wake-up line for an active user request).

Service is called by EthIf in case a wake-up interrupt is detected.

Requests the Ethernet Transceiver Driver to create a Transmission Secure Association in the Transceiver. The Short Secure Channel Identifier is included to support XPN configurations. Tags: atp.Status=DRAFT

Requests the Ethernet Transceiver to update the SecY/PAC of the PHY with the provided parameters. A Transmission Secure Channel with the provided SCI shall be configured during the first call. A pointer to a MACsec Basic Parameters Configuration file shall be provided to create the Secure Channel. Tags: atp.Status=DRAFT

Obtains the baud rate of the indexed transceiver

This function returns the least recent wakeup reasons.

Retrieves the cable diagnostics result of a given transceiver.

Obtains the duplex mode of the indexed transceiver

Obtains the link state of the indexed transceiver

Obtains the media access mode of the transceiver when EthTrcvDuplexMode is configured as ETHTRCV_DUPLEX_MODE_HALF

Obtains the PHY identifier of the Ethernet Transceiver according to IEEE 802.3-2015 chapter 22.2.4.3.1 PHY Identifer.

Obtains the current signal quality of the link of the indexed transceiver

Obtains the state of the indexed transceiver

Returns the wake up mode of t he indexed transceiver Tags: atp.Status=obsolete

Returns the version information of this module

Initializes the Ethernet Transceiver Driver

Request the Ethernet Transceiver Driver to create a Reception Secure Association in the Transceiver. The Short Secure Channel Identifier is included to support XPN configurations. Tags: atp.Status=DRAFT

Requests the Ethernet Transceiver Driver to create a Transmission Secure Association in the Transceiver. The Short Secure Channel Identifier is included to support XPN configurations. Tags: atp.Status=DRAFT

Request the Ethernet Transceiver Driver to remove the Reception Secure Association identified by the provided Association Number. Tags: atp.Status=DRAFT

Request the Ethernet Transceiver Driver to remove the Transmission Secure Association identified by the provided Association Number. Tags: atp.Status=DRAFT

Request the Ethernet Transceiver Driver to provide MACsec statistics. Tags: atp.Status=DRAFT

Request the Ethernet Transceiver Driver to return the Packet Number that is used for the next packet in the given Transmission Secure Association. Tags: atp.Status=DRAFT

Requests the Ethernet Transceiver Driver to configure a Reception Secure Channel for the given Secure Channel Identifier. Tags: atp.Status=DRAFT

Requests the Ethernet Transceiver Driver to reset to default the MACsec values of the Reception Secure Channel for the given Secure Channel Identifier. Tags: atp.Status=DRAFT

Requests to set the Controlled Port enabled parameter of a PAE. Tags: atp.Status=DRAFT

Request the Ethernet Transceiver Driver to update the Reception Secure Association with the given Packet Number. The Active parameter is included to change the specified AN status. Tags: atp.Status=DRAFT

Requests the Ethernet Transceiver to update the SecY/PAC of the PHY with the provided parameters. A Transmission Secure Channel with the provided SCI shall be configured during the first call. A pointer to a MACsec Basic Parameters Configuration file shall be provided to create the Secure Channel. Tags: atp.Status=DRAFT

Requests the Ethernet Transceiver Driver to update the Transmission Secure Association with the given Packet Number. The Active parameter is included to change the specified AN status. Tags: atp.Status=DRAFT

Used for polling state changes and wakeup reasons. Calls EthIf_TrcvModeIndication when the transceiver mode changed. Stores wakeup events if EthTrcvWakeUpSupport is set to ETHTRCV_WAKEUP_BY_POLLING.

Called when information has been read out via MII interface. Triggered by previous Eth_Read Mii call. Can directly be called within Eth_ReadMii.

Trigger the cable diagnostics for the given Ethernet transceiver.

Activates a given loopback mode.

Activates a given test mode.

Activates a given transmission mode.

Enables / disables the indexed transceiver

Enables / di sables the wake - up mode or clear the wake - up reason of the indexed transceiver Tags: atp.Status=obsolete

Restarts the negotiation of the transmission parameters used by the indexed transceiver

Request the Ethernet Transceiver Driver to create a Reception Secure Association in the Transceiver. The Short Secure Channel Identifier is included to support XPN configurations. Tags: atp.Status=DRAFT

Request the Ethernet Transceiver Driver to provide MACsec statistics. Tags: atp.Status=DRAFT

Request the given link state for the given transceiver

Called when information has been written via MII interface. Triggered by previous Eth_WriteMii call. Can directly be called within Eth_WriteMii.

This type defines the Ethernet baud rate. The baud rate gets either negotiated between the connected transceivers or has to be configured.

Describes the results of the cable diagnostics.

Implementation specific structure of the post build configuration

This type defines the Ethernet duplex mode. The duplex mode gets either negotiated between the connected transceivers or has to be configured.

This type defines the Ethernet link state. The link state changes after an Ethernet cable gets plugged in and the transceivers on both ends negotiated the transmission parameters (i.e. baud rate and duplex mode)

This type defines the media access control type in half duplex. If ETHTRCV_MAC_TYPE_PLCA is configured, PLCA is supported and the parameters listed in ECUC_EthTrcv_00055 have to be configured. Tags: atp.Status=draft

Describes the possible PHY loopback modes

Describes the possible PHY test modes

Describes the possible PHY transmit modes

Status supervision used for Development Error Detection. The state shall be available for debugging.

This type controls the transceiver wake up modes and/ or clears the wake - up reason. Tags: atp.Status=obsolete

This type defines the transceiver wake up reasons.

This callout is invoked to determine whether the configuration options contained in a received SD message match the ones configured in the local SD configuration (i.e., SdServerCapability Record or SdClientCapabilityRecord).

Enabling or Disabling ACL policy check for all service instance

Update Service ACL SdClientServiceAllowedProviders or SdServerServiceAllowedConsumers depending on Client or Server service by adding or removing this IP address. Tags: atp.Status=draft

Initializes the Service Discovery.

Callback function, which will be provided to SoAd to be able to trigger the ACL policy check or explicitly grant access on the received Method call request Tags: atp.Status=draft

Indication of a received PDU from a lower layer communication interface module.

Starts a preconfigured SdServiceGroup. For example, OfferService entries will be sent out after the call of Sd_ServiceGroupStart() for all ServerServives of a SdServiceGroup, which are not requested yet.

Notification about a SoAd socket connection state change, e.g. socket connection gets online

This type defines the modes to indicate the current mode request of a Client Service.

This type defines the Client states that are reported to the BswM using the expected API Sd_Client ServiceSetState.

Type for a zero-terminated string of configuration options.

Configuration data structure of Sd module.

This type defines the subscription policy by consumed EventGroup for the Client Service.

This type defines the subscription policy by consumed EventGroup for the Client Service.

This type defines the subscription policy by EventHandler for the Server Service.

This type defines the Server states that are reported to the SD using the expected API Sd_Server ServiceSetState.

The AUTOSAR ServiceDiscovery module's SdServiceGroup object identifier.

This service closes the socket connection specified by SoConId.

This service requests to copy data for transmission to the buffer indicated. This call is triggered by TcpIp_Transmit(). Note: The call to <Up>_CopyTxData() may happen in the context of Tcp Ip_Transmit().

Disables routing of a group of PDUs in the SoAd related to the RoutingGroup specified by parameter id. Routing of PDUs can be either forwarding of PDUs from the upper layer to a TCP or UDP socket of the TCP/IP stack specified by a PduRoute or the other way around specified by a SocketRoute.

Disables routing of a group of PDUs in the SoAd related to the RoutingGroup specified by parameter id only on the socket connection identified by SoConId.

Enables routing of a group of PDUs in the SoAd related to the RoutingGroup specified by parameter id. Routing of PDUs can be either forwarding of PDUs from the upper layer to a TCP or UDP socket of the TCP/IP stack specified by a PduRoute or the other way around specified by a SocketRoute.

Enables routing of a group of PDUs in the SoAd related to the RoutingGroup specified by parameter id only on the socket connection identified by SoConId.

Allows to read and reset detailed measurement data for diagnostic purposes. Get all MeasurementIdx's at once is not supported. SOAD_MEAS_ALL shall only be used to reset all MeasurementIdx's at once. A NULL_PTR shall be provided for MeasurementDataPtr in this case.

Retrieves the local address (IP address and port) actually used for the SoAd socket connection specified by SoConId, the netmask and default router

Retrieves the physical source address of the EthIf controller used by the SoAd socket connection specified by SoConId.

Retrieves the remote address (IP address and port) actually used for the SoAd socket connection specified by SoConId

Returns socket connection index related to the specified TxPduId.

Returns current state of the socket connection specified by SoConId.

Returns the version information.

Triggers the transmission of all If-TxPDUs identified by the parameter id after requesting the data from the related upper layer.

Triggers the transmission of all If-TxPDUs identified by the parameter id on the socket connection specified by SoConId after requesting the data from the related upper layer.

Requests transmission of a PDU.

Initializes the Socket Adaptor.

API allows to check if a communication over this socket connection is possible for a dedicated remote address. It includes that the socket connection is bound to a socket, a physical address is available for the requested remote address and if a security association is configured that a secured connection is already established.

This service gets called by the TCP/IP stack if an IP address assignment changes (i.e. new address assigned or assigned address becomes invalid).

Schedules the Socket Adaptor. (Entry point for scheduling)

This service opens the socket connection specified by SoConId.

By this API service an upper layer of the SoAd can read the currently configured hostname, i.e. FQDN option in the DHCP submodule of the TCP/IP stack.

By this API service the local IP address assignment used for the socket connection specified by SoConId is released.

By this API service the remote address (IP address and port) of the specified socket connection shall be released, i.e. set back to the configured remote address setting.

By this API service the local IP address assignment which shall be used for the socket connection specified by SoConId is initiated.

The TCP/IP stack calls this primitive after the reception of data on a socket. The socket identifier along with configuration information determines which module is to be called.

By this API service the remote address (IP address and port) of the specified socket connection shall be set.

This API service shall either return the socket connection index of the SoAdSocketConnection Group where the specified remote address (IP address and port) is set or assign the remote address to an unused socket connection from the same SoAdSocketConnectionGroup.

This service gets called if the stack put a socket into the listen mode before (as server) and a peer connected to it (as client). In detail: The TCP/IP stack calls this function after a socket was set into the listen state with TcpIp_TcpListen() and a TCP connection is requested by the peer.

This service gets called if the stack initiated a TCP connection before (as client) and the peer (the server) acknowledged the connection set up. In detail: The TCP/IP stack calls this function after a socket was requested to connect with TcpIp_TcpConnect() and a TCP connection is confirmed by the peer. The parameter value of SocketId equals the SocketId value of the preceeding TcpIp_TcpConnect() call.

of the event just encountered. Parameters (inout) None Parameters (out) None Return value None Description This service gets called if the stack encounters a condition described by the values in Event.

Requests cancellation of an ongoing reception of a PDU in a lower layer transport protocol module.

Requests cancellation of an ongoing transmission of a PDU in a lower layer communication module.

Request to change a specific transport protocol parameter (e.g. block size).

Requests transmission of a PDU.

The TCP/IP stack calls this function after the data has been acknowledged by the peer for TCP. Caveats: The upper layer might not be able to determine exactly which data bytes have been confirmed.

By this API service an upper layer of the SoAd can set the hostname, i.e. FQDN option in the DHCP submodule of the TCP/IP stack.

Indication of a received PDU from a lower layer communication interface module.

Within this API, the upper layer module (called module) shall check whether the available data fits into the buffer size reported by PduInfoPtr->SduLength. If it fits, it shall copy its data into the buffer provided by PduInfoPtr->SduDataPtr and update the length of the actual copied data in PduInfoPtr->SduLength. If not, it returns E_NOT_OK without changing PduInfoPtr.

The lower layer communication interface module confirms the transmission of a PDU, or the failure to transmit a PDU.

This function is called to provide the received data of an I-PDU segment (N-PDU) to the upper layer. Each call to this function provides the next part of the I-PDU data. The size of the remaining buffer is written to the position indicated by bufferSizePtr.

This function is called to acquire the transmit data of an I-PDU segment (N-PDU). Each call to this function provides the next part of the I-PDU data unless retry->TpDataState is TP_ DATARETRY. In this case the function restarts to copy the data beginning at the offset from the current position indicated by retry->TxTpDataCnt. The size of the remaining data is written to the position indicated by availableDataPtr.

This function is called at the start of receiving an N-SDU. The N-SDU might be fragmented into multiple N-PDUs (FF with one or more following CFs) or might consist of a single N-PDU (SF). The service shall provide the currently available maximum buffer size when invoked with TpSdu Length equal to 0.

Called after an I-PDU has been received via the TP API, the result indicates whether the transmission was successful or not.

This function is called after the I-PDU has been transmitted on its network, the result indicates whether the transmission was successful or not.

This function gets called by the SoAd if an IP address assignment related to a socket connection changes (i.e. new address assigned or assigned address becomes invalid).

Notification about a SoAd socket connection state change, e.g. socket connection gets online

Configuration data structure of the SoAd module.

Index to select specific measurement data

RoutingGroup identifier type for unique identification of a SoAd routing group. The size of this type depends on the maximum number of routing groups which is specified by configuration parameter SoAdRoutingGroupMax.

SoCon identifier type for unique identification of a SoAd socket connection. The size of this type depends on the maximum number of socket connections which is specified by configuration parameter SoAdSoConMax.

type to specify the state of a SoAd socket connection.

Returns the version information of this module.

Initializes the SOME/IP TP module.

This function performs the processing of the AUTOSAR SOME/IP TP module's reception activities.

This function performs the processing of the AUTOSAR SOME/IP TP module's transmission activities.

Indication of a received PDU from a lower layer communication interface module.

Requests transmission of a PDU.

Within this API, the upper layer module (called module) shall check whether the available data fits into the buffer size reported by PduInfoPtr->SduLength. If it fits, it shall copy its data into the buffer provided by PduInfoPtr->SduDataPtr and update the length of the actual copied data in PduInfoPtr->SduLength. If not, it returns E_NOT_OK without changing PduInfoPtr.

The lower layer communication interface module confirms the transmission of a PDU, or the failure to transmit a PDU.

This type shall contain at least all parameters that are post-build able according to chapter 10.

This service requests to copy data for transmission to the buffer indicated. This call is triggered by Tcp Ip_ Transmit(). Note: The call to _ Copy Tx Data() may happen in the context of Tcp Ip_ Transmit().

This API is called by Tcp Ip in case the Duplicate Address Detection (DAD) is enabled and detecting a duplicate IP Address.

By this API service the configured ICMP message handler function is called by the TCP/ IP stack on reception of a ICMP message which is not handled by the TCP/ IP stack.

This service gets called by the TCP/ IP stack if an IP address assignment changes (i.e. new address assigned or assigned address becomes invalid).

This API is called by Tcp Ip in case of a change in the ARP/ NDP table related to the controller specified by Ctrl Idx.

The TCP/ IP stack calls this primitive after the reception of data on a socket. The socket identifier along with configuration information determines which module is to be called.

This service gets called if the stack put a socket into the listen mode before (as server) and a peer connected to it (as client). In detail: T he TCP/ IP stack calls this function after a socket was set into the listen state with Tcp Ip_ Tcp Listen() and a TCP connection is requested by the peer.

This service gets called if the stack initiated a TCP connection before (as client) and the peer (the server) acknowledged the connection set up. In detail: The TCP/ IP stack calls this function after a socket was requested to connect with Tcp Ip_ Tcp Conn ect() and a TCP connection is confirmed by the peer. The parameter value of Socket Id equals the Socket Id value of the preceeding Tcp Ip_ Tcp Connect() call.

Service .

This function queries the current time. This information will be requested when assembling the client hello message.

This callback is used for the TLS server to provide the CSM key name according to the key identification that was selected by the TLS client. The TLS server must provide a CSM Key reference to a key that matches this key identification name.

Queries the Identity hint for a pr e - shared key ciphersuite. This information is transmitted by the TLS Server to provide its identification to the TLS client.

The TCP/ IP stack calls this function after the data has been acknowledged by the peer for TCP. Caveats: The upper layer might not be able to determine exactly which data bytes have been confirmed.

Service TcpIp_Bind.

By this API service the TCP/ IP stack is requested to change a parameter of a socket. E.g. the Nagle algorithm may be controlled by this API.

By this API service the TCP/ IP stack is requested to close the socket and release all related resources.

By this API service the TCP/ IP stack retrieves DHCP option data identified by parameter option for already received DHCP options.

By this API service the TCP/ IP stack retrieve s DHCPv6 option data identified by parameter option for already received DHCPv6 options.

By this API service the TCP/ IP stack writes the DHCPv6 option data identified by parameter option.

By this API service the TCP/ IP stack writes the DHCP option data identified by parameter option.

Allows to read and reset detailed measurement data for diagnostic purposes. Get all Measurement Idx's at once is not supported. TCPIP_ MEAS_ ALL shall only be used to reset all Measurement Idx's at once. A NULL_ PTR shall be provided for Measurement Data Ptr in this case.

Copies entries from the physic al address cache of the IPv4 instance that is active on the Eth If controller specified by ctrl Idx into a user provided buffer. The function will copy all or number Of

Tcp Ip_ Get Ctrl Idx returns the index of the controller related to Local Addr Id.

Service TcpIp_GetIpAddr.

Copies entries from the physic al address cache of the IPv6 instance that is active on the Eth If controller specified by ctrl Idx into a user provided buffer. The function will copy all or number Of

Obtains the physical source address used by the Eth If controller implicitly specif ied via Local Addr Id.

Tcp Ip_ Get Remote Phys Addr queries the IP/ physical address translation table specified by Ctrl Idx and returns the physical address related to the IP addres s specified by Ip Addr Ptr. In case no physical address can be retrieved and parameter init Res is TRUE, address resolution for the specified IP address is initiated on the local network.

Returns the version information.

Service TcpIp_IcmpTransmit.

By this API service the TCP/ IP stack sends an ICMPv6 message according to the specified parameters.

This service initializes the TCP/ IP Stack. Tcp Ip_ Init may not block the start - up process for an indefinite amount of time. Caveats: The call of this service is mandatory before using the Tcp Ip instance for further processing.

Schedules the TCP/ IP stack. (Entry point for scheduling) AUTO SAR CP R20 - of Document ID : AUTOSAR_SWS_TcpIp

By this API service the local IP address assignment for the IP address specified by Local Addr Id shall be released.

By this API service the TCP/ IP stack is requested to change the Tcp Ip state of the communication network identified by Eth If controller index.

Service TcpIp_RequestIpAddrAssignment.

Resets all learned IP - addresses to invalid values.

By this API service the TCP/ IP stack gets an indication and the data of a received frame.

B y this API service the TCP/ IP stack is requested to establish a TCP connection to the configured peer.

By this API service the TCP/ IP stack is requested to listen on the TCP socket specified by the socket identifier. Available v ia Tcp Ip.h

By this API service the reception of socket data is confirmed to the TCP/ IP stack.

Service TcpIp_TcpTransmit.

This service transmits data via UDP to a remote node. The transmission of the data is immediately performed with this function call by forwarding it to Eth If.

Tcp Ip_ Arp Cache Entries elements type

Configuration data structure of the Tcp Ip module.

Tcp Ip address families.

Events reported by Tcp Ip.

IPv6 address assignment policy.

Specifies the state of local IP a ddress assignment

Address identification type for unique identification of a local IP address and Eth If Controller configured in the Tcp Ip module.

Index to select specific measurement data

Tcp Ip_ Ndp Cache Entries elements type

Type TcpIp_ParamIdType.

Protocol type used by a socket.

Tcp Ip specific return type.

This structure defines a IPv6 address type which can be derived from the generic address structure via cast. AUTO SAR CP R20 - of Document ID : AUTOSAR_SWS_TcpIp

This structure defines an IPv4 address type which can be derived from the generic address structure via cast.

Generic structure used by APIs to specify an IP address. (A specific address type can be derived from this structure via a cast to the specific struct type.)

Socket identifier type for unique identification of a Tcp Ip stack socket. TCPIP_ SOCKETID_ INVALID shall specify an invalid socket handle.

Specifies the Tcp Ip state for a specific Eth If controller.

TLS connection identifier type for unique identification of a TLS connection. TCPIP_ TLSCONNECTIONID_ INVALID shall specify an invalid TLS connection handle.

IP6 address wildcard.

IP address wildcard.

Local Addr Id wildcard.

Port wildcard.

NM indicate to activate the transmission of PN shutdown messages on the given NM-Channel. This results in transmission of a NM-PDU with PNSR bit set to 1 (PN shutdown message). ▽ △

Check if remote sleep indication takes place or not. Cave ats: Udp Nm is initialized correctly. Configuration: Optional (only available if Udp Nm Remote Sleep Ind Enabled == true)

NM indicate to deactive the transmission of PN shutdown messages on the given NM-Channel. This result in transmission of a usual NM-PDUs with PNSR bit set to 0.

Disable the NM PDU transmission ability due to a ISO14229 Communication Control (0x28) service Caveats: Udp Nm is initialized correctly. Configuration: Optional (Only available if Udp Nm Com Control Enabled == true)

Enable the NM PDU transmission ability due to a ISO14229 Communication Control (0x28) service Caveats: Udp Nm is initialized correctly. Configuration: Optional (Only available if U dp Nm Com Control Enabled == true).

Service Name Udp Nm_ Get Local Node Identifier Syntax Std_ Return Type Udp Nm_ Get Local Node Identifier ( Network Handle Type nm Channel Handle, uint8* nm Node Id Ptr ) Service ID [hex] 0x07 Sync/ Async Synchronous Reentrancy Reentrant Parameters (in) nm Channel Handle Identification of the NM - channel Parameters (inout) None Parameters (out) nm Node Id Ptr Pointer where node identifier of the local node shall be copied to. Return value Std _ Return - Type E_ OK: No error E_ NOT_ OK: Getting of the node identifier of the local node has failed or is not configured for this network handle. Descri ption Get node identifier configured for the local node. Caveats: Udp Nm is initialized correctly. Available via Udp Nm.h

Get node identifier from the most recently received NM PDU. Caveats: Udp Nm is initialized correctly.

Get the whole PDU data out of the most recently received NM message. Caveats: Udp Nm is initialized correctly.

Returns the state and the mode of the network management. Caveats: Udp Nm is initia lized correctly. Configuration: Mandatory

Get user data from the most recently received NM message. Cave ats: Udp Nm is initialized correctly. Configuration: Optional (Only available if Udp Nm User Data Enabled == true).

This service returns the version information of this module.

Initialize the complete Udp Nm module, i.e. all channels which are activated at configuration time are initialized. A UDP socket shall be set up with the TCP/ IP stack. Caveats: This function has to be called after initialization of the TCP/ IP stack. Configuration: Mandatory

Main function of the Udp Nm which processes the algorithm describes in that document. E.g.: Udp Nm_ Main Function_0() represents the Udp Nm instance for the UDP chann el 0 Udp Nm_ Main Function_1() represents the Udp Nm instance for the UDP channel 1

Release the network, since ECU doesn't have to communicate on the bus. Network state shall be changed to 'released'. Caveats: Udp Nm is initialized correctly. Configuration: Optional (Only available if Udp Nm Passive Mode Enabled == false)

Request the network, since ECU needs to communicate on the bus. Network state shall be changed to 'requested' Caveats: Udp Nm is initialized correctly. Configuration: Optional (Only available if Udp Nm Passive Mode Enabled == false)

Passive startup of the AUTOSAR Udp Nm. It triggers the transition from Bus - Sleep Mode or Prepare Bus Sleep Mode to the Network Mode in Repeat Message State. Caveats: Udp Nm is initialized correctly.

Set Repeat Message Request Bit and Partial Network Learning Bit for NM messages tran smitted next on the bus. This will force all nodes on the bus to enter the PNC Learning Phase. This is needed for the optional Dynamic PNC - to - channel - mapping feature. Tags: atp.Status=draft

Service to indicate that an NM message with set Repeat Message Re- quest Bit has been received. This is needed for node detection and PNC dynamic learning.

Set Repeat Message Request Bit for all NM messages transmitted on the bus after this function has returned without error. Available vi a Udp Nm.h

Request bus synchronization. Caveats: Udp Nm is initialized correctly. Configuration: Optional (only available if Udp Nm Bus Synchronization Enabled==true and Udp Nm Passive Mode Enabled ==false).

Requests transmission of a NM - PDU with PNSR bit set to 1 (PN shutdown message) Tags: atp.Status=draft

Set the NM Coordinator Sleep Ready bit in the Control Bit Vector

Set user data for all NM messages transmitted on the bus after this function has returned without error. Caveats: Udp Nm is initialized correctly. Configuration: Optional (Only available if Udp Nm User Data Enabled==true and Udp Nm Passive Mode Enabled==false).

Indication of a received PDU from a lower layer communication interface module.

Within this API, the upper layer module (called module) shall check whether the available data fits into the b uffer size reported by Pdu Info Ptr - >Sdu Length. If it fits, it shall copy its data into the buffer provided by Pdu Info Ptr - >Sdu Data Ptr and update the length of the actual copied data in Pdu Info Ptr - >Sdu Length. If not, it returns E_ NOT_ OK without ch anging Pdu Info Ptr.

The lower layer communication interface module confirms the transmission of a PDU, or the failure to transmit a PDU.

Requests transmission of a PDU.

-

Used to define the position of the control bit vector within the NM PACKET.

Provides access to a transmit buffer of the specified controller

Read out values related to the receive direction for a received packet. For example, this could be RSSI or Channel belonging to one single packet.This API is valid only within the context of WEth_ Receive

Read out values related to the transmit direction for a transmitte d packet. For example, this could be transaction ID belonging to one single packet.This API is valid only within the context of WEth_ Tx Confirmation.

Obtains the state of the indexed controller

Obtains the physical source address used by the indexed controller

Returns the version information of this module

Returns the following list according to IEEE 802.11 - 2012, where the maximal possible value shall denote an invalid value, e.g. if this counter is not available: 1. dot11STAStatistics Transmitted F ragment Count 2. dot11STAStatistics Group Transmitted Frame Count 3. dot11STAStatistics Failed Count 4. dot11STAStatistics Retry Count 5. dot11STAStatistics Multiple Retry Count 6. dot11STAStatistics Frame Duplicate Count 7. dot11STAStatistics RTSSuccess C ount 8. dot11STAStatistics RTSFailure Count 9. dot11STAStatistics ACKFailure Count 10. dot11STAStatistics Qos Transmitted Fragment Count 11. dot11STAStatistics Qos Failed Count 12. dot11STAStatistics Qos Retry Count 13. dot11STAStatistics Qos Multiple Retr y Count 14. dot11STAStatistics Qos Frame Duplicate Count 15. dot11STAStatistics Qos RTSSuccess Count 16. dot11STAStatistics Qos RTSFailure Count 17. dot11STAStatistics Qos ACKFailure Count 18. dot11STAStatistics Qos Received Fragment Count 19. dot11STAStat istics Qos Transmitted Frame Count 20. dot11STAStatistics Qos Discarded Frame Count 21. dot11STAStatistics Qos MPDUs Received Count 22. dot11STAStatistics Qos Retries Received Count 23. dot11STAStatistics Received Fragment Count 24. dot11STAStatistics Grou p Received Frame Count 25. dot11STAStatistics FCSError Count 26. dot11STAStatistics Transmitted Frame Count 27. dot11STAStatistics RSNAStats CMACICVErrors 28. dot11STAStatistics RSNAStats CMACReplays 29. dot11STAStatistics RSNAStats Robust Mgmt CCMPReplays 30. dot11STAStatistics RSNAStats TKIPICVErrors 31. dot11STAStatistics RSNAStats TKIPReplays 32. dot11STAStatistics RSNAStats CCMPDecrypt Errors 33. dot11STAStatistics RSNAStats CCMPReplays 34. dot11STAStatistics Transmitted AMSDUCount 35. dot11STAStatisti cs Failed AMSDUCount 36. dot11STAStatistics Retry AMSDUCount 37. dot11STAStatistics Multiple Retry AMSDUCount 38. dot11STAStatistics AMSDUAck Failure Count 39. dot11STAStatistics Received AMSDUCount 40. dot11STAStatistics Transmitted AMPDUCount 41. dot11ST AStatistics Transmitted MPDUs In AMPDUCount 42. dot11STAStatistics AMPDUReceived Count 43. dot11STAStatistics MPDUIn Received AMPDUCount 44. dot11STAStatistics AMPDUDelimiter CRCError Count 45. dot11STAStatistics Implicit BARFailure Count 46. dot11STAStati stics Explicit BARFailure Count 47. dot11STAStatistics Channel Width Switch Count 48. dot11STAStatistics Twenty MHz Frame Transmitted Count 49. dot11STAStatistics Forty MHz Frame Transmitted Count 50. dot11STAStatistics Twenty MHz Frame Received Count 51. dot11STAStatistics Forty MHz Frame Received Count 52. dot11STAStatistics PSMPUTTGrant Duration 53. dot11STAStatistics PSMPUTTUsed Duration 54. dot11STAStatistics Granted RDGUsed Count 55. dot11STAStatistics Granted RDGUnused Count 56. dot11STAStatistics Tr ansmitted Frames In Granted RDGCount 57. dot11STAStatistics Dual CTSSuccess Count 58. dot11STAStatistics Dual CTSFailure Count 59. dot11STAStatistics RTSLSIGSuccess Count 60. dot11STAStatistics RTSLSIGFailure Count 61. dot11STAStatistics Beamforming Frame Count 62. dot11STAStatistics STBCCTSSuccess Count 63. dot11STAStatistics STBCCTSFailure Count 64. dot11STAStatisticsnon STBCCTSSuccess Count 65. dot11STAStatisticsnon STBCCTSFailure Count

Returns the following list according to IEEE 802.11 - 2012, where the maximal possible value shall denote an invalid value, e.g. if this counter is not available: 1. dot11STAStatistics Transmitted Octets In AMSDUCount 2. dot11STAStatistics Receiv ed Octets In AMSDUCount 3. dot11STAStatistics Transmitted Octets In AMPDUCount 4. dot11STAStatistics Received Octets In AMPDUCount 5. dot11STAStatistics Transmitted Octets In Granted RDGCount

Request transmission of an Ethernet frame, where each upper layer a header part as element of a single linked list. All headers together with the payload form an entire Ethernet frame Tags: atp.Status=draft

Initializes the Wireless Ethernet Driver

Support for indirect transmissions (extended frame timing constraints) and mechanisms for channel selection when using multiple channels. Used for polling state changes. Calls Eth If _ Ctrl Mode Indication when the controller mode changed.

Reads a transceiver register

Triggers frame reception.

Set values related to the transmit direction for a specific buffer (packet to be sent). For example, this can be the desired transmit power or the channel belonging to one single packet.

Enables / disables the indexed controller

Sets the physical source address used by the indexed controller

Triggers transmission of a previously filled transmit buffer

Triggers transmission of a previously filled transmit buffer that is waiting in a software priority queue.

Triggers frame transmission confirmation

Update the physical source address to/ from the indexed context filter. If the Wireless Ethernet Controller is not capable to do the filtering, the software has to do this.

Configures a transceivers registers or triggers a function offered by the receiver

Wir eless radio parameters for a packet that has been received.

Wireless radio parameters for a packet that has to be transmitted.

Implementation specific structure of the post build configuration

Read values related to the receive direction of the transceiver. For example, this could be a Channel Busy Ratio (CBR) or the average Channel Idle Time (CIT).

Obtains the link state of the indexed transceiver

Ob tains the state of the indexed transceiver

Returns the version information of this module

Initializes the Wireless Ethernet Transceiver Driver

Used for polling state changes. Calls Eth If_ Trcv Mode Indication when the transceiver mode changed.

Set values related to the receive direction of a transceiver's wireless channel .For example, this could be a channel parameter like the frequency.

Set values related to the transmit direction of a transceiver's wireless channel. For example, this could be the bitrate of a channel.

Set values related to a transceiver's wireless radio. For example, this could be the selection of the radio settings (channel, ...).

Enables / disables the indexed transceiver

Bandwidth of a radio channel

Implementation specific structure of the post build configuration

Wireless channel properties of the receive side

Radio operation mode with multiple radio channel configurations

Power of frame, in 0.5 d Bm units, raw value 0 equals - 100 d Bm

Wireless channel settings for the receive side

-

Wireless radio settings for the transceiver

Power of frame, in 0.5 d Bm units, raw value 0 equals - 100 d Bm